Settings, saved consumables, and inspection records remain distinct for each machine.
Edit saved wire, gas & power
REMEMBERED BETWEEN VISITS
Shop defaults
Set these when changing spool, gas bottle, or power supply. Every weld lookup will reuse them.
Factory lookup is verified here only for 240V, C25, ER70S-6, DCEP, .030″ and .035″. Other combinations show “No verified chart” rather than guessing.
STEP 2 · WELD DETAILS
Configure a weld
Material, joint & position
Choose the joint, then the position. F (fillet) and G (groove) are built into the position designation; you don't need a separate weld-type selection. Wire and gas are remembered per machine.
PER WELD
STEP 3 · YOUR GUIDANCE
Your welding guidance
MILLER MILLERMATIC 211 CURRENT WELD
1/4″ Open corner
1F · flat fillet.030″ ER70S-6C25 · 240V
YOUR SAVED SHOP BASELINE
6.75/70
Voltage dial / wire-speed dial
MILLER FACTORY CHART
7.5/80
Thickness reference only · sticker 267706-A
!Not a qualified weld procedure. The factory values are thickness references, and your personal values are practice starting points.
WHAT TO DO NEXT
Push · cursive-eSMALL LOOPS
Motion: Make small, tightly overlapping loops with a continuous arc, watching both toes of the puddle. This is a schematic, not a prescribed weave width.
Settings: WeldBook will not automatically change voltage or wire speed for this motion. Loops can slow forward travel and increase local heat/deposition. Test on a matching coupon, inspect for undercut, excessive buildup and fusion, and save a separate baseline only after evaluation.
Values are voltage dial / wire-speed dial, not actual volts or IPM. Manufacturer starting references do not account for fit-up, welding position, or joint strength requirements.
Choose MIG C25, MIG C100, or flux-cored mode to match your consumables.
Press PowerSet.
Select the wire diameter and metal thickness. For dissimilar thicknesses, Everlast says to select the thicker material.
Read the voltage and wire-feed speed displayed on your welder. Test, adjust as appropriate, and record the actual values in WeldBook.
Some PowerSet combinations are unavailable and are blocked on the machine. The manual does not publish numerical voltage/IPM values per thickness; do not treat the table above as numeric settings.
These numbers are not from Everlast. They are comparison starting points for flat mild-steel practice coupons, not joint-specific instructions. Prefer the Cyclone's PowerSet function and document the settings it actually displays.
240V · C25 · .030″ ER70S-6 · flat reference
Steel
Voltage
Wire feed
3 · Your personal setting: Save a separate, actually tested V/IPM pair below for each machine, thickness, joint, position and travel technique. Personal values do not replace qualification evidence.
Save or edit a tested personal baseline
PER-CONFIGURATION BASELINE
Your starting settings
Settings are saved only for an exact match of this weld's inputs and shop defaults. They are not qualified procedures.
Joint and qualification check
Position codes already include weld classification: F denotes a fillet weld and G denotes a groove weld. For an open corner, both may be possible; check the actual weld detail before selecting 1F versus 1G. Mixed-thickness and structural welding require matching test coupons and approved procedures.
YOUR FABRICATION HISTORY
Personal welding log
Data and backups
Records are saved on this device. When signed in and paired, text records and saved photos are also synchronized privately to Supabase. Export JSON before import, device changes, or troubleshooting.
SAFETY & EVIDENCE
Qualification workflow
Not qualified
A structured practice-and-evidence checklist. Completing it creates a documented review record, not an AWS certification, approved WPS, or permission to weld a load-bearing chassis part.
Readiness evidence0 of 7
Work through the steps below. Each item requires real evidence.
For structural / suspension components
Do not move from practice coupons to production frame or suspension welds solely because a photo shows penetration or a checklist is complete. Confirm joint design, fatigue loading, weld procedure, and required inspection with the manufacturer or a qualified welding professional.